it would seem the jack is a double TIP , with a SLEEVE wiper to augment the Ground connection . You may cutaway the trace of the SLEEVE wiper from the 2 TIP trace . Then jumper this to the ground trace. You can now use a TS pl55 plug into the jack as a speaker out.
noelmem1
Search found 165 matches
- Sat Nov 25, 2023 6:28 am
- Forum: Power Amplifiers
- Topic: CS-800 1/4" outputs shorted from factory?
- Replies: 5
- Views: 2768
- Sun Oct 09, 2022 8:28 pm
- Forum: Processors/Effects
- Topic: Memory Problem Dual Deltafex
- Replies: 4
- Views: 6634
Re: Memory Problem Dual Deltafex
oh yes ,i have pulled cleaned , lubed with oil based contact cleaner the 28 pin Chip in the socket - the primary unreliable socket connection- they should have used the gold plated round hole sockets .
noelmem1
noelmem1
- Sun Oct 09, 2022 8:25 pm
- Forum: Processors/Effects
- Topic: Memory Problem Dual Deltafex
- Replies: 4
- Views: 6634
Re: Memory Problem Dual Deltafex
cleaned the board with Contact cleaner and brush , drying it today under the sun , then let me try it out tonite , if still , then there are 6 opamps to try replace . The TDS220 Tek scope is out of commission due to old display - darn LCDs they die after 20 years .
noelmem1
noelmem1
- Sun Oct 09, 2022 8:22 pm
- Forum: Speakers/Enclosures
- Topic: Peavey sp2g
- Replies: 4
- Views: 2311
Re: Peavey sp2g
oh yes , but still the horn in the sp5G ( CH3) is smaller , so still he will lose mids and throw
in the SP2G CH945.. something like that
i seldom visit , im outdated
noelmem1
in the SP2G CH945.. something like that
i seldom visit , im outdated
noelmem1
- Sun Oct 09, 2022 10:02 am
- Forum: Club Peavey
- Topic: Enzo
- Replies: 32
- Views: 21783
Re: Enzo
Goodbye and rest in peace Douglas - the repair guru .
i remember him writing ..." To start fixing a tubeamp - whack the cabinet top with your fist"
noelmem1
i remember him writing ..." To start fixing a tubeamp - whack the cabinet top with your fist"
noelmem1
- Sun Oct 09, 2022 9:42 am
- Forum: Speakers/Enclosures
- Topic: Peavey sp2g
- Replies: 4
- Views: 2311
Re: Peavey sp2g
you will lose mids as the compression driver of the SP5G is 14XT , the SP2G has the 22XT .
I suggest you run mono and feed the 2 SP5G from one amp channel , and the 2 SP2s from the other , Pad the amp for the SP5Gs .
noelmem1
I suggest you run mono and feed the 2 SP5G from one amp channel , and the 2 SP2s from the other , Pad the amp for the SP5Gs .
noelmem1
- Sun Oct 09, 2022 9:01 am
- Forum: Processors/Effects
- Topic: Memory Problem Dual Deltafex
- Replies: 4
- Views: 6634
Re: Memory Problem Dual Deltafex
my unit now has sort of steady tinny crackle that goes louder with the reverb effect . I dont see any battery for the memory - they could have used a Flash Memory chip . Somebody went in to fix this before it went to ebay as the glue supposed to be on top of the screw was under it. I will try the sc...
- Sun Feb 21, 2021 5:59 am
- Forum: Power Amplifiers
- Topic: CS800x - DDT light blink, almost no output
- Replies: 4
- Views: 4371
Re: CS800x - DDT light blink, almost no output
The cs800 cs800X has a DDT defeat switch and Bridge switch you might like to cycle them 50 times . There is also a PL2 engage switch when a Lo-Z input is used or canned crossover-not directly related but you might like to cycle that switch too 50 times. Could be a hanged ground connection and hi fre...
- Sat Feb 20, 2021 8:39 pm
- Forum: Speakers/Enclosures
- Topic: Replacement Diaphram for 22A Driver?
- Replies: 12
- Views: 5441
Re: Replacement Diaphram for 22A Driver?
The replacement kit RX22N from peavey read .. it is compatible with 22A
RX™ 22N Diaphragm Kit
show image: null
RX™ 22N Diaphragm Kit
Installation InstructionsCut Sheet
Item No: 03617300
$59.99
RX™ 22N Diaphragm Kit
show image: null
RX™ 22N Diaphragm Kit
Installation InstructionsCut Sheet
Item No: 03617300
$59.99
- Sat Feb 20, 2021 7:46 pm
- Forum: Speakers/Enclosures
- Topic: Replacement Diaphram for 22A Driver?
- Replies: 12
- Views: 5441
Re: Replacement Diaphram for 22A Driver?
look for 22XT genuine replacement , RX22 has different phase plug , i dont know about the 22XTn? or RX22n . Pry some more as the gasket is just stuck tight from overtightening . Genuine replacement comes with a new gasket . If you can buy a sachet of Ferrofluid then put it into the gap after cleanin...
- Mon Apr 06, 2020 6:10 pm
- Forum: Speakers/Enclosures
- Topic: Peavey PR12 Crossover Frequency
- Replies: 4
- Views: 3956
Re: Peavey PR12 Crossover Frequency
the crossover has a ptc rxe030 in series with the compression driver coil . But no resistor-bulb accross it .
both can go -the coil and the ptc when overdriven long time.
noelmem1
both can go -the coil and the ptc when overdriven long time.
noelmem1
- Tue Dec 11, 2018 7:54 am
- Forum: Mixers
- Topic: PV6 - old version
- Replies: 1
- Views: 1851
Re: PV6 - old version
my unit still works , this is the non usb model of 2007 I guess .
- Tue Dec 11, 2018 7:39 am
- Forum: Power Amplifiers
- Topic: CS 800X Strange Channel Issues
- Replies: 2
- Views: 3281
Re: CS 800X Strange Channel Issues
could be the relays among many other possibilities , try gentle screwdriver handle knock on those , see if the output comes alive just like when the handle was smacked with a hammer.
if the pcb live parts doesnt touch the chassis ...no need to put insulators - they will jut gather dust
noelmem1
if the pcb live parts doesnt touch the chassis ...no need to put insulators - they will jut gather dust
noelmem1
- Tue Jan 30, 2018 8:42 am
- Forum: Speakers/Enclosures
- Topic: Need Schematics peavey crossover sp2 xt circuit diagram
- Replies: 3
- Views: 4861
Re: Need Schematics peavey crossover sp2 xt circuit diagram
it could just be a 5 component crossover , easily traced . From main input to horn passes through a cap , the horn is shunted with a coil . To the woofer via a iron core coil , the woofer is shunted with a C or an RC . The direct connect jack to the woofer is just an insert . To the horn is also lik...
- Tue Jan 30, 2018 8:33 am
- Forum: Speakers/Enclosures
- Topic: Using Spacers on Black Widow Magnets to Correct Voicecoil Manufacturing Variance Errors?
- Replies: 2
- Views: 2435
Re: Using Spacers on Black Widow Magnets to Correct Voicecoil Manufacturing Variance Errors?
could be the surround or the spider . Perhaps they need break-in to settle to the correct position.
noelmem1
noelmem1